收藏本站
ADE7758
Data Sheet
OPERATIONAL MODE REGISTER (0x13)
The general configuration of the ADE7758 is defined by writing to the OPMODE register. Table 18 summarizes the functionality of each
bit in the OPMODE register.
Table 18. OPMODE Register
Bit
Bit
Default
Location
0
1
2
3 to 5
Mnemonic
DISHPF
DISLPF
DISCF
DISMOD
Value
0
0
1
0
Description
The HPFs in all current channel inputs are disabled when this bit is set.
The LPFs after the watt and VAR multipliers are disabled when this bit is set.
The frequency outputs APCF and VARCF are disabled when this bit is set.
By setting these bits, the ADE7758 ADCs can be turned off. In normal operation, these bits should
be left at Logic 0.
DISMOD[2:0]
Description
0
1
0
0
0
0
Normal operation.
Redirect the voltage inputs to the signal paths for the current channels and
the current inputs to the signal paths for the voltage channels.
0
1
0
0
1
1
Switch off only the current channel ADCs.
Switch off current channel ADCs and redirect the current input signals to the
voltage channel signal paths.
0
1
1
1
0
0
Switch off only the voltage channel ADCs.
Switch off voltage channel ADCs and redirect the voltage input signals to the
current channel signal paths.
0
1
1
1
1
1
Put the ADE7758 in sleep mode.
Put the ADE7758 in power-down mode (reduces AI DD to 1 mA typ).
6
SWRST
0
Software Chip Reset. A data transfer to the ADE7758 should not take place for at least 166 μs after
a software reset.
7
Reserved
0
This should be left at 0.
MEASUREMENT MODE REGISTER (0x14)
The configuration of the PERIOD and peak measurements made by the ADE7758 is defined by writing to the MMODE register. Table 19
summarizes the functionality of each bit in the MMODE register.
Table 19. MMODE Register
Bit
Bit
Default
Location
0 to 1
2 to 4
Mnemonic
FREQSEL
PEAKSEL
Value
0
7
Description
These bits are used to select the source of the measurement of the voltage line frequency.
FREQSEL1
FREQSEL0
Source
0
0
Phase A
0
1
Phase B
1
0
Phase C
1
1
Reserved
These bits select the phases used for the voltage and current peak registers. Setting Bit 2 switches
the IPEAK and VPEAK registers to hold the absolute values of the largest current and voltage
waveform (over a fixed number of half-line cycles) from Phase A. The number of half-line cycles is
determined by the content of the LINECYC register. At the end of the LINECYC number of half-line
cycles, the content of the registers is replaced with the new peak values. Similarly, setting Bit 3 turns
on the peak detection for Phase B, and Bit 4 for Phase C. Note that if more than one bit is set, the
VPEAK and IPEAK registers can hold values from two different phases, that is, the voltage and
current peak are independently processed (see the Peak Current Detection section).
5 to 7
PKIRQSEL
7
These bits select the phases used for the peak interrupt detection. Setting Bit 5 switches on the
monitoring of the absolute current and voltage waveform to Phase A. Similarly, setting Bit 6 turns on
the waveform detection for Phase B, and Bit 7 for Phase C. Note that more than one bit can be set for
detection on multiple phases. If the absolute values of the voltage or current waveform samples in
the selected phases exceeds the preset level specified in the VPINTLVL or IPINTLVL registers the
corresponding bit(s) in the STATUS registers are set (see the Peak Current Detection section).
Rev. E | Page 64 of 72
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ADE7761AARSZ-RL IC ENERGY METERING 1PHASE 20SSOP
ADE7761BARSZ-RL IC ENERGY METERING 1PHASE 20SSOP
ADE7768ARZ-RL IC ENERGY METERING 1PHASE 16SOIC
ADE7769ARZ-RL IC ENERGY METERING 1PHASE 16SOIC
ADM8843ACPZ-REEL7 IC LED DRVR WHITE BCKLGT 16LFCSP
ADP1653ACPZ-R7 IC LED DRVR PHOTO FLASH 16-LFCSP
ADP1712-EVALZ BOARD EVALUATION ADP1712
ADP1720-EVALZ BOARD EVAL FOR ADP1720-ADJ
相关代理商/技术参数
ADE7759 制造商:AD 制造商全称:Analog Devices 功能描述:Active Energy Metering IC with di/dt Sensor Interface
ADE7759ARS 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSRL 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSZ 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSZRL 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7760 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection
ADE7760ARS 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP 制造商:Analog Devices 功能描述:ENERGY METER IC W/ ONCHIP FAULT & OSCIL. - Rail/Tube
ADE7760ARSRL 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP T/R 制造商:Analog Devices 功能描述:ENERGY METER IC W/ONCHIP FAULT & OSCIL. - Tape and Reel